- 542
- 8 438 909
Brandon Bicasso
United States
Приєднався 11 жов 2009
I'm Brandon and I Rebuild Motorcycles! No idea what I'm doing so let's learn together.
Відео
Sportster Exhaust Upgrade #Motorcycle
Переглядів 2,7 тис.День тому
Indian Motorcycle Won’t Release This Valuable Information
Переглядів 3,8 тис.3 дні тому
💭 Okay, "Hacking".. not really. More like sniffing. Most modern motorcycles have this network called CANBUS. Essentially, it allows each sensor to see what data other sensors are putting out. Makes the wiring less complicated (even though CAN is) by reducing the amount of wires running to each sensor. I bought a device to read the data off the diagnostic port in an attempt to get the ride comma...
Clip-On Install On A Sportbike! #motorcycle
Переглядів 2,9 тис.11 днів тому
#hondamotorcycles #motorcycle
Solving A Speed Wobble Problem! #motorcycle
Переглядів 11 тис.14 днів тому
#indianmotorcycle #motorcycle
How To Install A Wheel, Tire, Rotor! (Motorcycle)
Переглядів 11 тис.15 днів тому
#motorcycle #indianmotorcycle
Something Is Not Right... Solving Another Indian Chief Problem
Переглядів 3,4 тис.16 днів тому
💭 Well, this is awkward. Not knowing how the speed sensor works on these bikes. Dang electronics.. Since getting this bike together, one issue I’ve had was with the rear speed sensor. Today, I figure out 100% what the problem is. 🤝 Support my effort to get more people on motorcycles here at Patreon: www.patreon.com/BrandonBicasso 🎵 Music Credit: C Y G N - Time to Chill chll.to/14d7acfb #Brandon...
Wrecked In A Ditch... How Much To Restore It? (CBR650R)
Переглядів 2 тис.17 днів тому
💭 The question.. does it make sense to rebuild a wrecked bike? I breakdown every dollar used to rebuild this CBR650R. 🤝 Support my effort to get more people on motorcycles here at Patreon: www.patreon.com/BrandonBicasso 🎵 Music Credit: Enough Cereals - Suave chll.to/77516075 #BrandonBicasso #HondaMotorcycle
Stealership Buy, Hidden Trauma… 24 More Hours With Indian Challenger
Переглядів 10 тис.18 днів тому
💭 A friend brought a 2020 Indian Challenger by the garage for a flat tire repair. Indian Challengers showing up is becoming a frequent thing. Unfortunately, this would be more than a routine fix. The pivot bolt that allows removing the tire without removing the exhaust was jammed. I work through that problem to get this bike back on the road while finding hidden trauma that made this job diffic...
Why Loctite Is Super Important! (Motorcycle Engine)
Переглядів 17 тис.19 днів тому
#motorcycle #indianmotorcycle
The Silly Reason My Motorcycle Wouldn’t Start (Sportster)
Переглядів 9 тис.20 днів тому
#motorcycle #harleydavidson
I think the engine looks way worse than last gen unfortunately. Looks plastic and generic
Fair opinion on that.
Friction riding is key in SF! My 2020 S60 does well when slow riding but cooks the hell out of my legs lol
lol, gotta get up to high way speeds and cool that thang off. 😂
Looks better without the covers.
The bike is gone
Just get the mans hos just goddamn pipe lol
😂😂😂
Buying a 2012 Victory and I have to tell you ... wow.
Awesome 👍
Who Brandon, your a awesome brother, he won the bike came, personalized it, spent time with you, and rode it back to California wow
Not sure how much more painting you're going to do but I assume you'll get a couple more copart vehicles and will need to paint something. I would check out SprayWayCustoms here on YT. he explains a lot about painting and why you do some of the things you have to. His is cars put painting is painting when it comes to cars or bikes.
great in-depth video!
guessing the fuse popped cause of the lights being torn off. that's my guess
Sort of. Wires touched in the hand control cluster.
Damn near ready to trade my 2018 triumph bobber for this
I have a soft spot for the Bonneville Bobber.
Deep
Man that bike you did a most Excellent job
That a super chief????
U bought another Limited super chief
This bike has been fixed and was a giveaway bike.
Yea I seen the date, you know your stuff
@@BrandonBicasso man but I'm going to get a bike from you
Cruise control is already possible on earlier model scouts. Look up MCCruise cruise control. I have it on my scout and it works great. 🤙
I rented one for a weekend ride on a whim. The clutch was horrible and it hated any RPM less than 4000.
She's a bit irritable in the low rpms.
I gave up buss diagnostics long ago. Best of luck. You are doing well.
Always test ride it, even when u do hidden things happen
Facts
Scraping pegs is the best.
I really do enjoy it haha.
Polaris/Indian OWN the programming they use. The only way to access it is to do it through a dealer OR make a deal with them to purchase all the equipment AND the license to use the computer. Fully legal.
Digital Wrench still requires dealer logins to activate certain equipment. Either a Dealer or its limited in function.
Normally you have to married the cluster with ecm to open its communications then it will accept the data,so probably oem scan tool. On aftermarket ecm is where we use reversed can bus
For Chief, that’s more to do with the WCM communicating with the ECM after the fob is recognized. Chief will start and run without the screen attached if the fob is present.
This was quite educational.
i tried to get that muffler twice from parts giant and they kept sending me the silver one, still debating if i should try to get it again. Anyway did you had to modify adjust anything after you installed the muffler? And those lights are crazy. I have the 2019 M90 Boulevard
Nah, you can put these on and ride without damaging anything. Can reach better performance with an ECM flash, though.
Man…I’d love to I love to have one and it is the reason why I’m watching this video although I own a Goldwing. I looked at before I bought my goal wing because they were so sweet, but I only had money to spend on a motorcycle one time and the motorcycle had to have an excellent maintenance, which does the Goldwing does, but I’m still drawn to the Victory motorcycle. But this was a very informative video. Thank you.
As you have noticed the actual data can be in a different byte or bit location within the CANbus packet. I would start with one sensor that both bikes have and capture the whole packet from each. Start comparing them in binary format. Find a USB serial to CANbus adapter and send your own packet to the screen and see if the value changes. You can use the PC to send a hex string out a serial port to the CANbus adapter into the bike. Good luck!
Great feedback. I haven't gotten a chance yet to mess with Scout, but will keep that info in my pocket!
I sent you a email with my number on it.
Duuuuuude so when is the indian garage opening?! Doooooo it!
No time soon haha. I'd do it if I had more space. Taking it day by day. Waiting on you to upload more on the Sporty!
Can I buy the Chief limited
Do what makes you happy br
I hope you pull this off bro!!
Hey bro, do you still hv the super chief limited
Yep, still have it.
Well the new scout can come with that screen....you would think you could get a data falsh for it to work.
New Scout has new wiring and modules like Chief to make everything work. Fuel pump tech is different too. Wish it were that easy.
@@BrandonBicasso ahhhhhhh. That sucks.
I'm lost. Too bad you don't live close by. When my warranty is up, I'll need help with any ride command issues I may have because I am not computer or electronic savvy. Hopefully someone around here is.
You'll be fine. Ride command is pretty stable tbh. If something happens to the screen, the bike can function without it. I think it'll last a good while.
Hi Brandon, I'm here for it. 😊
🤯🤯🤯🤕🤕
Good luck with that, you lost me when you opened the garage door 😲
Is there any other applications that this could be used for other than utilizing a ride command on a scout? Also, would you have to use this same application to utilize a ride command display on a regular chief 111?
Yeah, of course. It’s a blank micro controller that can be coded to do many things. Also, ride command on regular Chief is plug and play. Just have to buy the other pieces to make the nav work.
I love that you have the patience for that. Good luck. I hope you'll figure it out. PS: Did you try reaching out to your Indian contacts? Maybe they'd be willing to help out. Off the record, of course 😉.
Lol, they won’t. I have access to some ECM dumps but those won’t help me with this project.